Generally the GRBL settings are almost good right out of the box and often don't need too much work to tweak them in. What stepper motors are you using and or lead screws and the pitch of those etc. Now you need another program to start to play with the whole thing and setting up the parameters. Thanks to all those who helped and added to this list. Scandinavia Swedish, Suomi - Finnish, Norsk - Norwegian.Try a language closer to your native language: Performing the above actions may help resolve your problem without further help. On Windows C:\Users\AppData\Roaming\ArduinoCreateAgent-1.1.On Linux ~/ArduinoCreateAgent-1.1/config.ini.On macOs ~/Applications/ArduinoCreateAgent-1.1/ArduinoCreateAgent.app/Contents/MacOS/config.ini.Boards using a MICRO USB connector need a cable that is both DATA and CHARGE.Unless using EXTERNAL PROGRAMMERS please leave the IDE selection at default “AVRISP mkII”.NANO ( NEW Types) Install your board CORE’s.NANO ( ALL Types) See the specific sections lower in the forum.NANO (Old Types) some require you to use the OLD BOOTLOADER option.CH340/341 based clones do not report useful information to the “get board info” button.Preferably install IDE’s as ADMINISTRATOR or your OS equivalent.Close the IDE before using any other serial programs.Avoid cloud/network based installations where possible OR ensure your Network/Cloud software is RUNNING.You may be selecting the wrong COM port.There may be a problem with the PC try RESTARTING it.Ensure you turn off any additional security / antivirus just to test.Close any other serial programs before opening the IDE.Remove any items connected to pins 0 and 1.There may be a problem with the board check or remove your wiring first.CH340/341 or CP2102 or FT232 VCP Drivers - FTDI You may not have the correct driver installed.Where possible use USB 2.0 ports or a USB 2.0 POWERED HUB to rule out USB 3.0 issues.Check you have a COMMON GROUND where required.Ensure you have FULLY inserted the USB cables.Remember that the people trying to help cannot see your problem so give as much information as you can.Duplicate accounts are NOT allowed and any extra may be deleted.Add working links to any specific hardware as needed ( NOT links to similar items).Add a SCHEMATIC were needed even if it is hand drawn.Add your sketch where applicable but please use CODE TAGS.How to insert an image into your post.Use quote or CODE tags to add error messages as an attachment NOT a picture.Always list the version of the IDE you are using and the board version if applicable.Your OS and version can be valuable information, please include it along with extra security you are using.Mention if you are using AI generated code it is important information.It will help you get the very best out of the forum in the future. The people who try to help with your project. If you don’t follow the guidelines all that happens is there is a long exchange of posts while we try to get you to tell us what we need in order to help you, which is frustrating for you and frustrating for us. Being new here you might think this is having rules for the sake of rules, but that is not the case. Please read and follow the instructions below. This guide explains how to get the best out of this forum. ![]() Get the best out of this forum Installation & Troubleshooting Long version.Please take a few moments to Learn and Use the Forum. I also recommend reading below for future reference in the forum. Again the internet is full of help so if you google "grbl settings" I am sure you will get the basics of what to do next. When you are ready for that stage come back to this post and let people know you are ready to set up your machine itself. This will be your first major task as you will probably find that the movements do not correspond to the measurements you are using. My preference for basic getting to grips with laser work is LASER GRBLĪlmost any program you use for GRBL will also allow you to fine tune the movement parameters as well. Once that is done you can forget about the IDE as such.įrom here on in you will need another program to send G-CODE to the UNO which will translate that into machine commands to move the axis on your laser engraver. There are multiple sources for loading GRBL onto your Arduino once you have installed the lib.īut for brevity you open the IDE then select the GRBL EXAMPLE you installed earlier and then use the IDE to upload it to the UNO. Then you need to INSTALL that library into the IDE. You then need to get and install the current version of GRBL First off install the IDE from here but select 1.8.9 version for now.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |